Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 2 Next »

v3.3.0.0

  • Can now add just vertical loads. This should help reduce size of loading grid

  • Fix for flag saying second order effects increased moments by more than 40% when it did not

  • Summary sketch now adds bar diameters for larger bar sizes

  • Added override for 225 psi check when calculating maximum transverse spacing

  • Fix issue where erection results were not being shown on performance summary

v3.2.0.0

  • Stability and Performance Improvements

  • Quality of life improvements

  • Fixed issue with eccentricities not updating / displaying properly for point loads

  • Fix issue where transverse spacing was computed incorrectly

v3.1.2.0

  • Fixed issue where transverse reinforcement was not being found in the analysis

  • Fixed problem where analysis could get stuck using reinforcement interrupts

v3.1.1.0

  • 3D model updated to now correctly show load orientations (used to be strictly positive)

  • Fixed typos and tweaked some input labels for clarity

  • Added service reactions to service tab

  • Fix issue where the transverse spacing was not being calculated correctly.

  • Updated 3D model view cube to mirror inputs on previous tabs.

v3.0.0.0

  • Detailed Flexure Capacity

    • New output tab, in analysis report, showing a detailed calculation of the flexure capacity

    • In this you will find the calculation for: PM Diagram, Biaxial Capacity Contour, Calculation of neutral axis depth, calculation of capacity, calculation of axial capacities

  • Transverse Reinforcement Changes

    • Added J-Hooks

    • Expanded Detailing Options

  • Datum Based Input

    • Concrete extents now defines a top elevation and bottom elevation

    • Inputs that ask for elevation are no longer from the bottom

    • Old files will open with the bottom elevation as 0

  • Expanded error handling

    • Analysis and design errors expanded to provide more information

  • Table Redesign

    • All tables redesigned with better formatting

    • Conditional formatting in table to highlight failures and the controlling row

  • Added an other load type which can be used for any load not present previously (Barrier Cables, Flood, Impact, etc)

  • Can now apply a displacement at the supports to simulate story drift

  • Minimum prestress is now an option to use the maximum or average amount. Previously, average could run into problems, due to transfer, where it would drop the average below 225 psi

  • Fix issue where load eccentricity was not updating in load grid

  • Column stack was removed. To do a column stack model it in a single file with moment releases.

  • Fixed interface bugs

  • Optimized analysis for speed increase

v2.2.2.0

  • Fix crash in 2nd order analysis

  • Fix issue where load eccentricity was not updating in load grid

v2.2.1.0

  • No longer display error 2nd order effect error for very small moments (< 0.01 kip-ft)

  • Fix error that was causing issues with the maximum spacing calculation for transverse reinforcement

v2.2.0.0

  • Add a read-only eccentricity column to the loading table

  • Ignore center strand / rebar not set to true by default

  • No longer display error 2nd order effect error for very small moments (< 0.01 lb-in)

  • Fixed a few issues causing crashes

  • Now uses either the section or structural sections bounding box for loading reference

  • Unified output locations to be in feet

  • Fix issue preventing load patterning from being enabled

  • Fix issue where maximum transverse spacing was incorrect

v2.1.1.0

  • Fixed display error on shear and flexure graph for strength combinations

v2.1.0.0

  • Removed kl/r > 100 check. Now correctly check that 2nd order effects do not increase demand by more than 40%.

  • Added triangular voids

  • Can now add custom analysis points from the file menu

  • Can now add custom result points from the file menu

  • Fixed errors in the drawing routines

  • Fix deflection reporting error

  • Fix printing error

  • No labels